How to choose suitable metal 3D printing materials to produce molds?

Dec 29, 2025

1. Material selection determined by application scenarios: varied needs for injection molding and die casting
The main factors that determine the material to use are the type of mold and how it will be used. diverse processes have quite diverse needs for material properties:
An injection mold needs to be able to handle the high temperature and pressure of melted plastic. The material should be able to conduct heat well, resist corrosion, and withstand thermal fatigue. For instance, the automobile interior mold employs 316L stainless steel powder, and the construction of a conformal cooling water channel shortens the injection molding cycle from 120 seconds to 75 seconds, raising the yield rate to 98%. XM-7 mold steel powder, which has a thermal conductivity of 30W/(m · K), may speed up the cooling of products and promote the chemical corrosion biting process. This meets the fine processing needs of shallow patterns (depth<0.12mm).
Die casting mold: It must be able to handle high-temperature metal liquid erosion and thermal stress cycles. The material must also be very durable, wear-resistant, and resistant to cracking from heat. Due to its heat treatment hardness of 50–52HRC, 1.2709 (18Ni300) martensitic aged steel powder has become the best choice for aluminum alloy die-casting molds. Using this material in the die-casting mold of a certain car engine cylinder has enhanced the mold's life from 20,000 uses to 60,000 uses and cut the cost per piece by 40%.
Rubber tire mold: The pattern blocks need to be very precise and resistant to wear, and they need to manage heat deformation to keep the product from flashing. The SLM technology used to print the CX (Corrax) stainless steel powder mold gives it a polishing capability of up to A2 level. The mold's weight is cut by 30% thanks to an optimized lattice support system, and the accuracy of pattern replication is enhanced to within 0.01mm.
2. Matching the properties of the material: Four main indications set the limits for performance.
Four aspects must be taken into account when evaluating the performance of mold materials: mechanical qualities, thermal properties, corrosion resistance, and process adaptability.
Properties of mechanics: The mold's ability to hold weight is based on its tensile strength, yield strength, and elongation at break. For instance, 1.2709 powder has a tensile strength of 2000MPa, which makes it good for die-casting situations with a lot of stress. 316L powder has a fracture elongation of 45%, which makes it better for thin-walled injection molds that need to be strong.
How well it works in the heat: The cooling efficiency and dimensional stability are affected by the thermal conductivity and the thermal expansion coefficient. XM-7 mold steel has a thermal conductivity that is 100% higher than 316L. This can greatly shorten the injection molding cycle. Invar 36 alloy (with a thermal expansion coefficient of 1.2 × 10⁻⁶/℃) is used for optical molds to keep them from losing accuracy due to thermal deformation.
Corrosion resistance: If you want to protect against corrosive plastics like PVC and PA, choose stainless steel with a high chromium concentration. 316L powder has 17% chromium, which helps keep surfaces smooth in humid conditions and cuts down on the need for maintenance.
Adaptability of the process: The quality of the print is affected by the powder's flowability, oxygen content, and sphericity. For instance, powders with a particle size distribution of 15–53 μm can eliminate interlayer flaws that happen when powder spreads unevenly. The impact toughness of 316L powder with an oxygen level of less than 100PPM is 44% higher than that of regular materials, which greatly extends the life of the mold.
3. Adaptability of the process: working together to improve equipment and post-processing
The choice of materials must be carefully coordinated with the printing process and the flow of post-processing:
Compatibility of equipment: Different metal 3D printing technologies need different materials. The SLM process works well with materials that have a high melting point, such titanium alloys and 1.2709. The binder jetting approach works better with cheap iron-based powders. For instance, a certain company made ZY6061 aluminum alloy powder that can be printed stably on EOS M290 equipment by improving the distribution of particle size and flowability. This solves the problem of cracking in regular 6-series aluminum alloys.
How to heat treat: To get rid of residual tension and improve their microstructure, printed materials need to be heated. The hardness of 17-4PH stainless steel powder can reach 42HRC after being aged at 480 ℃, which also gets rid of printing cracks. The impact toughness of XM-7 mold steel can be increased to 20J/cm ² using a graded quenching procedure, while its hardness stays at 30HRC.
Surface treatment: Depending on what the mold is for, you can choose electroplating, sandblasting, or chemical polishing. For example, shoe molds need to use nano electroplating to get a mirror effect, and die-casting molds need to use sandblasting to make the surface rougher and easier to remove.
4. Economic analysis: controlling costs over the whole life cycle
Material selection must strike a compromise between performance and cost, and whole lifecycle evaluation must be used to lower costs and enhance efficiency:
Cost of materials: There is a big difference in price between high-end materials. The unit price of 1.2709 powder is about 800 yuan/kg, which is three times the price of 316L (260 yuan/kg). However, it can last three times longer than regular H13 steel and is cheaper overall. The "base grafting" procedure can be used to print high-performance materials on traditional mold steel bases for small-scale production. This cuts down on the amount of material utilized.
How well manufacturing works: Materials with high heat conductivity can speed up injection molding cycles and make better use of equipment. Using XM-7 powder in a certain medical multi-cavity mold has cut the time it takes to make one component from 45 seconds to 30 seconds. The mold's worth has gone up by more than 2 million yuan a year.
Cost of maintenance: Materials that don't corrode can make it less often that you have to clean them. 316L molds can keep their flat surfaces even in humid conditions, which cuts maintenance expenses by 60% compared to regular P20 steel.

Send Inquiry