Will metal 3D printing affect the safety and compliance of energy equipment?

Jul 31, 2025

1. Technical Features: Innovation and Risk Coexist
Metal 3D printing makes parts by melting metal powder layer by layer. Its main advantage is that it can make complex shapes that are hard to make with traditional methods, like the cooling channels inside aircraft engine blades and the irregular connectors of nuclear power plant pressure vessels. But this technological characteristic also makes security vulnerabilities worse:
It's hard to avoid faults in materials: Metal powder particles are usually between 10 and 70 microns in size. When they are hit with a laser or electron beam, gas flow is easily created, which washes away the powder and makes microscopic holes or flaws. For instance, tests showed that a gas turbine blade made by an energy business employing 3D printing had a 0.1mm hole inside it. It didn't break right away, but it could develop fatigue cracks over time.
Challenge of process stability: Parts that shrink or change shape during sintering can cause cracks or changes in size. For example, if the sealing surface of 3D-printed parts isn't even because the shrinkage wasn't controlled properly, it could lead to nuclear leakage while making valves for nuclear power plants.
How hard is it to process after? There are processes in the adhesive spraying process, such degreasing and sintering, and if they are not done correctly, the pieces may be weaker. A certain wind power company made a gearbox bearing seat using this method, but it broke while it was in use because the density was too low after sintering since the degreasing wasn't done properly.
2. Security hazards range from network security to dust explosions.
Metal 3D printing is dangerous at every stage of the production process and directly threatens the safety of energy equipment.
Risk of dust explosions: When aluminium alloys and titanium alloys are in a semi-dry or wet state, they can react with water and release hydrogen gas, which can cause them to catch fire. In 2023, a technological business in Shanghai produced a horrible accident when a medium-efficiency purification box detonated because they used waste aluminium powder from water treatment illegally. Three people died and one person was hurt. These kinds of tragedies show that companies who make energy equipment may have to take on a lot of safety responsibility if they don't set up stringent dust control procedures.
Risk of suffocation from inert gas: If the argon or nitrogen gas used in the printing process leaks, it could drop the oxygen level in the operating room to less than 19.5%, which could lead to asphyxia mishaps. Three workers passed out in a locked workplace because a nuclear power equipment maker didn't put in gas leak alarms. This showed that there weren't enough safety precautions in place.
Risks to network security: 3D printing machines need very specific conditions to work properly, and hackers may change the laser power settings, which could make items that don't satisfy the strength standards. The US Department of Defence has given Velo3D's printers permission to connect to secret networks because they have received STIG compliance certification and can protect themselves from network threats. If organisations that make energy equipment don't pay attention to data security, they could risk having important parts hacked.
3. Regulatory adaptation: from specific legislation to general rules
In China's energy legal system, the rules governing metal 3D printing have created a multi-level framework:
Specific legal restrictions:
The Nuclear Safety Law says that companies that make equipment for nuclear power plants must keep 3D printing process data for at least 50 years and send in reports on how energy-efficient their products are on a regular basis.
The Oil and Gas Pipeline Protection Law says that important parts of pipelines must be tested for leaks and pressure, and 3D printed parts must have information on how to trace the materials used to make them.
Specifications for technical standards:
According to GB/T 35351-2017, metal powders for 3D printing must have a sphericity of at least 90% and an oxygen concentration of no more than 0.05%.
According to GB/T 39253-2020, the sintering process should include three steps: preheating, insulation, and cooling. The heating rate should be ≤ 5 °C/min to minimise shrinkage deformation.
Making industry oversight stronger:
According to the Energy Law, the energy regulatory department may visit the 3D printing workplace to check that the process parameters match the requirements of energy planning.
Market regulatory agencies demand energy equipment to pass either CCC certification or voluntary certification. 3D printed parts also need to send in separate reports that show the composition of the materials used.
4. Path to Compliance: Technological Breakthrough and Working Together for the Environment
Energy equipment manufacturers need to make sure that they are using metal 3D printing in a way that is compliant by doing the following:
New technical advances:
Creating a smart monitoring system, like Micron's "fastfab" software, that can keep an eye on the filter element's state, the substrate temperature, and the cabin pressure in real time to stop metal powder from building up and creating explosions.
Improve the sintering process: Use segmented sintering technology to precisely regulate the temperature curve and reduce part deformation. This method has helped Siemens Energy cut the deformation of combustion chamber printing from 3mm to 0.5mm,
Standard participation:
Take the lead in creating global standards: Encourage businesses to help make ISO/TC 261 standards and push for the use of Chinese technological solutions in international rules. Daqing Oilfield is in charge of the ISO 6398-1 standard, which addresses a gap in international standards for oil production equipment.
Set group standards: If there aren't any national standards in a certain field, publish group standards through industry groups. The China Additive Manufacturing Industry Alliance, for instance, has published the "Technical Specification for Metal Adhesive Spray Forming," which lays out important details like how to choose an adhesive and how to sinter it.
Working together in the industrial chain:
Set up a full chain traceability system that lets you share data and keep track of quality from powder preparation to printing and moulding. Bolite and AVIC Maite worked together to build a technology that has raised the certification rate of 3D printed aviation parts to 98%.
Create a digital management platform that uses the industrial Internet platform to combine data on how equipment is used and quality inspection reports. This will allow for dynamic compliance monitoring. The National Additive Manufacturing Innovation Centre built the "Additive Manufacturing Cloud Platform," which can keep an eye on the operation status of more than 3,000 3D printers in real time across the country.

https://www.china-3dprinting.com/metal-3d-printing/additive-manufacturing-of-aircraft-engine.html

Send Inquiry